* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
Carrier made by GIVI or recently SEA BASSOEM also has similar design. I think that the design property is far better than the plastic made by Carrier. On the other hand, although Cost performance is bad, compared to GIVI made or SEA BASSOEM, This Kappa make it much higher Cost performance. Since the appearance changes only about Seal, there is no choice but to choose this cheap product.
Installation difficulty is also very easy. If you give up, since the Screw lock material is applied to Bolt which carries the car body and Carrier to a large extent, it was hard enough to remove it.
As a disadvantage of the feeling of use, there is a protrusion to fix the box, Without it it became Flat and it was easier to use, but it can not be helped.
Anyway Manufacturer (GIVI and OEM) If I am not particular about it, I think it's a good one.
This bike was going to be going for a few longer distance rides and needed a few parts to be able to hook up the luggage already purchased. This rack was not hard to find as there are few that fit the VStrom anyway. The price from Webike was cheaper than I could source locally. With a few other small parts already in my basket, I ordered all together to save a bit on shipping. My order was shipped using EMS and all arrived safely in 5 days solid. The rack came in a nice box from Kappa. There were loys of instructions for fitting and the necessary parts included to fit correctly. Not a tricky fit but take your time as you really do need to get this right or you will lose your luggage at some point. Trust me, I know from past experience. All in all, this rack set up is perfect and the luggae fitted proper. Thanks Webike. View Detail
This is a GIVI OEM product; the GIVI part number is FZ1192. Compared to FZ1146, there are more parts and it took a little longer to install. Performance is as expected. The most important point is that the side case holder can now be attached.View Detail
I bought this for my cb125f fortune yamaha super jogzr wing black. the screw holes were out of alignment. i used a drill to enlarge one hole and was able to install it. I've been using it for a week for camping touring& daily commuting to and from school with no problems. (10,000km) It seems to be durable.View Detail
This product is used as a MONOKEYBase for GIVI's OEM Mounting Processing of Cover It is not difficult to make a hole in rear cover because there is a mark But you need hole size about 20mm This product comes with an opened-for-hole Urethane sponge Seal for protection You can
Installation of plates In the case of the M5Plate, after the Plate is installed in the Carrier, the body of the vehicle is Carrier can be installed It is very easy to avoid having to put your fingers in the gaps
In the case of M7Plate, it was impossible to install it without machining due to interference between the Grab Bar and Plate It wasView Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING